FREE Knitting Patterns, Yarn Reviews, Tutorials, Magazines

Home » KNITmuch » A Reversible Cable Pillow Cover with Honeycomb Stitch

A Reversible Cable Pillow Cover with Honeycomb Stitch

by Sondra Armas

This post covers a textured envelope pillow cover with two different cable sides. It covers swatching for gauge, a honeycomb front worked from the center out, and a back in two overlapping staghorn cable panels. It also covers finishing. The finished cover fits an 18″ [45.7cm] square pillow insert.

materials

yarn

  • textured yarn with a soft halo and crisp stitch definition (yardage is not stated, and the photos show about three balls)

needles

  • interchangeable needles, US 4 [3.5mm], with a short cable to start and a longer one as the piece grows
  • cable needle, or double-pointed needles for starting in the round

notions

  • stitch markers
  • 18″ square pillow insert
  • yarn needle for seaming

Swatch for gauge

Each side needs its own gauge, so swatch both. The honeycomb swatch on US 4 [3.5mm] needles measured 24 stitches and 20 rows over 3¾″ by 3″ after blocking. Each honeycomb shape covers 8 stitches and 8 rows and measures 1¼″ in both directions. That means the width must match the height as the piece grows outward.

The staghorn side is mostly stockinette and has a looser gauge of 4 stitches per inch.

Cast on for the center

Start with a slip knot, then alternate knit one and yarn over until you have 8 stitches. Divide them evenly across two needles, or pull the cable through between the fourth and fifth stitches. Join in the round and knit one round. Gently tug the tail to check that the center hole closes.

Repeat the knit one, yarn over increase to reach 16 stitches. Knit one round, then place markers to make four sections of 4 stitches. From here on, make increases instead of yarn overs, so the fabric has no gaps. Each section grows by two stitches per round, one in from each end. After four rounds, you have four sections of 8 stitches.

Work the honeycomb front

Set the pattern with four rounds that add a single cable and keep growing by two stitches per section. Then repeat a four-round pattern with a cable round followed by three plain rounds. Each cable round adds one more cable pair than the last, because eight stitches are added over four rounds.

Adding two stitches per round keeps the piece flat, so the center does not peak. Continue until the square measures 18″, which is about 116 stitches per side. Finish by adding a few reinforcement stitches at the center, so the puffy insert cannot catch on a weak spot.

Knit the staghorn back

The envelope back is worked flat in two panels with the overlap placed about a third of the way down. Staghorn cables are the bottom half of the honeycomb shape, so the two sides echo each other.

Cast on 74 stitches, which adds a couple of extra stitches to allow for cable tension. Work a four-row repeat of a cable row with plain stockinette rows between, with five cable repeats across and three plain stitches at each edge. Make the top panel about 7″ long. End on a wrong-side row, then work 6 rows (about 1″) of 2 by 1 ribbing and cast off. The ribbing continues the cable lines.

Make the bottom panel the same way, but work about 15″ before the ribbing, for a 16″ total. This panel is longer to allow plenty of overlap, since the insert is puffy and the honeycomb side has less give.

Finish the cover

Cast on the second panel from the opposite edge so the cables run in opposite directions where the panels meet. Seam the three pieces together with a yarn needle, then insert the pillow. Allow for the difference in stretch between the two sides. The back stretches more than the front.

Original series by Sue Sindrey on KNITmuch.com. Photos by Sue Sindrey

YOU MAY ALSO LIKE...

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.